Our Landescape aluminium Tandems began life in 2002 and are beautifully hand-made. If you think you know aluminium frames then think again!. Our high-quality Landescape Tandems are manufactured from tubing specifically made and drawn for Tandems. We use 7020T6 with a wall thicknesses of 1.8mm at the joints and butted to 1.4mm in the centre of the tubes. The post-weld strength of 7020T6 is greater and therefore gives a stronger, lighter frame than less expensive frames made from cheaper materials and sourced from the Far East. The material we use, its butting and lightness make for a stiffer frame with better power efficiency and handling but not at the expense of comfort.
With lightness and strength hand-in-hand, the standard offering of all our Landescape Tandems is that they are built-in custom sizes and in the Direct Lateral Design. You can be assured that we can build your Tandem to suit your exact needs. From track to trail, on or off-road or just pootling along, enjoying the countryside for a day or an extended tour, we have a Landescape Tandem for you.
From £5930, see below to add options and accessories. Configure your Tandem now!
Buy this Tandem with our 0% Finance or on our Cycle to Work Scheme. Read about specialist Tandem Insurance and also Servicing which with all Tandems purchased from us has 2 years of service included – go to our Services page here.
"We had 'The Tandem Experience', a really excellent introduction to riding a bicycle made for two. Very thorough training on technique for riding a tandem (hint: it's quite different to a normal bike), then a whole day hire of a touring tandem, with a very pleasant 25 mile circular route map supplied. Bike was very good quality, and training unhurried and well delivered. Highly recommended, if you're thinking of trying out a tandem!"James McRae, Local Guide - Google Review
A common question and one that we do take seriously as it makes the difference when riding a Tandem safely and for long term enjoyment.
How do we work this out?
All of our Landescape Tandems are built as a custom frame which simply means
We charge to produce a TandemCAD for you that is refundable once the Tandem is placed on order. Click below if you wish to go through this process.Go to our Custom Sizing here!
|Frame Size||A1/2 Top Tube F/R||B1/2 Seat Tube F/R||C2 Chainstay||D1/2 Bottom Bracket F/R||F Head Tube||H Wheelbase||K Fork Offset||O1/2 Standover||α Head Angle||β1/2 Seat Angle|
Many colours are available for Landescape Tandems in both Matt and Gloss finishes. We are also able to offer in any RAL colour too!
We offer three paint styles for your Landescape Tandem. Opaque, Roadline (shown) and Speedline
Landescape decals are available in White, Black and Silver. Fitted to Down Tube, Boom Tube and Headtube.
We can supply any pedals or you can fit your own if preferred.
Pedals commonly used are: Shimano - 324 SPD / Flat, Shimano - 520 SPD, Classic Alloy (as shown) and Studded Platform. Half Clips can be supplied to fit Shimano 324 and Classic Alloy.
Saddles offered are from: Bioflex Ongel Ozone (as shown) - in various widths. Brooks - all models and Selle Italia - all models.
We fit the correct size for use with the tyre width of your choice and they come in both Black & Silver. Available from Flinger (as shown) and SKS.
Supplied as Standard to the rear position is the Cane Creek Thudbuster ST G4 (as shown) or the System EX EL for a reduced cost.
Handlebars can be changed and the following are popular choices. Front - Jones Loop SG 64cm rise (as shown). Front/Rear - BLB Big Smoker Riser Bar 7.6cm rise. Rear - Profile Upturns 47cm wide.
Our Tandems are supplied with a standard adjustable rear stem, however depending on the sizes of both riders the rear handlebars may require to be higher. We supply a sleeve/stem combination to allow this to our existing rear stems. Please contact us to discuss the options. To fit seat post sizes of 27.2mm, 29.8mm and 31.6mm.
Racks for Panniers: Front/Rear - Tubus, Front/Rear - Blackburn and Rear - Topeak Super Tourist DX (as shown).
Panniers from Ortlieb & Topeak (as shown with drop down panniers).
Standard aluminium Pulse cages from Zefal and also the superb non cage bottles from Fabric (as shown) in two sizes and in clear or smoke.
Schmidt SON dynamo hub (as shown), superb Supernova E3 Pro 2 front light combined with Supernova 3 rear light. This package can be added to a Sinewave Cycles Reactor USB top cap charger for your USB-powered devices.
Sinewave Cycles Reactor USB top cap charger for your USB-powered devices.
Topeak Road Master Blaster to fit neatly into your frame for your on the move pressure top up and the Topeak Joeblow Turbo Floor Pump (as shown) to keep pressure topped up with ease.
Park Tool Peg Spanner SPA1 to fit all of our Tandem eccentrics. Combine this with a multi tool pack, puncture outfit and tyre levers and your ready for your travels.
To transport your Tandem on roof bars, rear of a Transporter or on a TowBar we have them all, please ask for more details.
On Tandems with a vertical quick release drop out we are able to supply as an e-assist upgrade at the point of order. Please contact us to discuss the options.
On some of our tandems a kickstand can be fitted to frame mount, ideal for touring Tandems. The Pletscher Twin leg stand is available in Silver or Black and 26"/27.5"/28"/292 wheels.
If there is a need for extra bosses for water bottles over the standard offer then this can be done.
This is a standard on our Landescape Tandems but is offered on our Co-Motion Tandems.
We offer on our Duratec, Landescape and Co-Motion Tandems the facility of a third/parking brake operated by either front or rear by a third lever. The brake and lever costs are additional to this upcharge.
If buying a Co-Motion or Landescape Tandem with Di2 then this upcharge is made to prepare the frame.
Touch Up can be ordered for all of our Tandems.
We recommend the Magura MDR-P 203mm Rotors fitted to our Landescape and Co-Motion Tandems. Offering a special patented interlocking of the outer and inner rings (Dovetail Interlink Technology) giving optimum braking performance even under heavy loads
To be used in conjunction with a drop handlebar to allow a conventional riding position.
Ergon - developed for riders seeking the most hand positions. The GP1 grip combined with a 5 finger multi-position bar end featuring rubberised inserts for a positive grip.
If you don’t know the size/saddle height you require:
If you do know the size/saddle height you require:
Get in touch on 01952 458340, or email on the link below. We’re here to help.Contact Us